HKM Website

	DPSI TWIN Double receiver = double safety! In addition to the redundant power supply, the DPSI TWIN now also ensures redundancy of the complete receiver. The TWIN version is based on the DPSI RV LDO and enables the use of two receivers, which can be automatically switched between, at your option (depending on signal quality). This means that for the first time the entire receiver station is doubly secured. A failsafe signal of the receiver is used to switch over to the second receiver in case of a failure. Thus a total of 8 channels are completely switched over and distributed to 25 servo outputs. For the first time, ALL servos can continue to be controlled in the event of a receiver failure. In addition to the failsafe function with automatic switching between two receivers (at the same frequency), it is also possible to use two receivers with different frequencies. Thus two completely separate (or different) transmitters can be used (and even two completely different receivers as well), which opens up unheard of possibilities. To obtain information about the status of the entire system, the DPSI ICE (Information Center) can be attached to the DPSI TWIN, as an option. All of the relevant information is displayed in this cockpit instrument (1.6" (40mm) diameter) by means of 8 LEDs (which receiver is currently active, how many interferences have occurred, are the batteries dying, etc.). It is then easy to tell after each flight whether any interferences occurred. This information can be used to promptly determine defective receivers and/or crystals, for example. In the case of a faulty range test, new positioning of the receiver or antennae - among other things - can be used to improve reception. It is thus possible to achieve qualitative improvements of the entire receiver system. It is also possible to communicate with a PC using the optional K/RS232 interface. The K-interface stems from the automobile industry and represents a simple bidirectional one-wire-interface. Thus a normal DPSI servo cable suffices as a connection between the DPSI TWIN and the K/RS323 interface for exchanging data with the PC. Using the PC software, it is possible to program the parameters of the DPSI TWIN (output voltage, stick positions, type of battery, etc.) All relevant operational parameters of the last flight are recorded by the data logger function of the DPSI TWIN and saved in non-volatile memory. Thus, if a model crashes, the cause of the crash can be determined without a doubt (due to interference in both receivers, for example, or to low voltage). Analysis of the causes of a potential crash is especially important for expensive models in order to rule out technical failure where applicable. DPSI_TWIN_instructions_V11_EN	DPSI TWIN w/ICE & Interface $525 DPSI TWIN only $396 DPSI ICE only $66 DPSI Interface only $79 external magnetic switch is also avaliable, please see Emcotec DPSI Accessories
	DPSI 2001 RV Battery Switch (Dual Power Supply) for 5/6 cell NiCad/NiMH, as well as LiIon/LiPo batteries (e.g. LONGGO) Regulated output voltage for receiver and servos (5.9 volts) 42 capacitors for efficient protection against over voltage peaks through the so called "dynamo effect" of high performance servos Two additional outputs (MPX connectors) providing the unregulated battery voltage for consumers with e.g. 7.4 volts (servos pumps) Current distribution of 10 receiver channels to 26 servos Dual electronically on/off switch, HF interference suppression, servo pulse amplification Intelligent voltage monitoring including optically and acoustically error indication Suitable to all battery types due to low drop out technology The used battery type can easily be programmed (and therefore the correct low voltage detection) Delivery includes switch actuator, MPX high current connectors, mounting parts, operation instructions Operation Instructions English (approx. 967 KB)	DPSI 2001 RV $305 in stock external magnetic switch is also avaliable, please see Emcotec DPSI accesories
	DPSI RV (new price since 01.01.2008!) Battery Switch (Dual Power Supply) for 5/6 cell NiCad/NiMH, as well as LiIon/LiPo batteries (e.g. LONGGO) Regulated output voltage for receiver and servos (from 5.0 volts up to 5.9 volts, adjustable in 4 steps) Current distribution of 12 receiver channels to 32 servos (additional servos directly connectable to receiver) Dual electronically on/off switch, HF interference suppression, servo pulse amplification Intelligent voltage monitoring including optically and acoustically error indication Suitable to all battery types due to low drop out technology The used battery type can easily be programmed (and therefore the correct low voltage detection) Three auxiliary outputs based on MPX high current connectors for the switched unregulated battery voltage, to supply servos with higher voltage Enlarged heat sink for better heat dissipation Delivery includes switch actuator, MPX high current connectors, 12 patch cables, operation instructions Operation Instructions English (approx. 967 KB)	DPSI RV $349 external magnetic switch is also avaliable, please see Emcotec DPSI Accessories
	DPSI RV Mini 6 (2008) Fully redundant power and servo management system of the latest generation Current distribution of 6 receiver channels to 7 servos (additional servos directly connectable to the receiver) Up to 50A peak current load for optimal servo power Failsafe electronical power switches with the proven pin switch actuator - the switching is not influenced by a micro controller (CSHC) Regulated output voltage for the use of all battery types SDVS - Selectable Dual Voltage Supply for discrete receiver and servo voltage provisioning: Receiver voltage switchable between 5.2V and 5.9V Servo voltage switchable between 5.9V and 7.4V LowDropOut regulators for minimum dissipation loss and maximum power Protection of the receiver against the so-called "dynamo effect" APP - Advanced Push-Pull servo pulse amplification - ideal for 2.4GHz applications HFIB - High Frequency Interference Blocking rejects interference from long servo cables IVM - Intelligent Voltage Monitoring with integrated status and alarm display Easily programmable for all battery types: NiCd, NiMH, Li-Ion, Li-Po or LiFePo4 Optical and acoustical error indication High grade ABS housing Delivery includes On/Off switch including mounting hardware, MPX high current connectors, 6 patch cables, operating instructions DPSI Mini 5/6 instructions	DPSI RV Mini 6 $265 DPSI RV Mini 6 Majic Includes Servo Match $315 external magnetic switch is also avaliable, please see Emcotec DPSI Accessories
	DPSI RV Mini 5 (2008) Fully redundant power and servo management system of the latest generation Current distribution of 5 receiver channels to 8 servos (additional servos directly connectable to the receiver) Up to 50A peak current load for optimal servo power Failsafe electronical power switches with the proven pin switch actuator - the switching is not influenced by a micro controller (CSHC) Regulated output voltage for the use of all battery types SDVS - Selectable Dual Voltage Supply for discrete receiver and servo voltage provisioning: Receiver voltage switchable between 5.2V and 5.9V Servo voltage switchable between 5.9V and 7.4V LowDropOut regulators for minimum dissipation loss and maximum power Protection of the receiver against the so-called "dynamo effect" APP - Advanced Push-Pull servo pulse amplification - ideal for 2.4GHz applications HFIB - High Frequency Interference Blocking rejects interference from long servo cables IVM - Intelligent Voltage Monitoring with integrated status and alarm display Easily programmable for all battery types: NiCd, NiMH, Li-Ion, Li-Po or LiFePo4 Optical and acoustical error indication High grade ABS housing Delivery includes On/Off switch including mounting hardware, MPX high current connectors, 5 patch cables, operating instructions DPSI Mini 5/6 instructions	DPSI RV Mini 5 $260 DPSI RV Mini 5 Majic Includes Servo Match $310 external magnetic switch is also avaliable, please see Emcotec DPSI Accessories
	DPSI VREG with switch actuator Dual Power Supply Interface with Voltage REGulator Regulated output voltage adjustable in three steps (5.3V / 5.6V / 5.9V) Additional output (MPX high current connector) providing the unregulated battery voltage for "high voltage" servos (7.4V) Electronic on/off switches controlled by the approved EMCOTEC switch actuator Enlarged heat sink for optimal heat dissipation Especially for use of LiPo batteries in receiving stations as well as 5 cell NiCad/NiMH batteries, A123 batteries, LiIon batteries Continuous current 8A, peak current 50A Integrated protection circuitry against the "dynamo effect" (voltage peaks generated by some servos) Delivery includes all accessories such as a switch actuator, MPX high current connectors, operating instructions DPSI VREG Instructions	DPSI VREG $165
	DPSI BIC V2.0 (black) incl. accessory kit Dual battery supply system with electronically on/off-switch and constantly regulated output voltage (5.9 volt) LC-display showing voltage, current, capacity, flight time and several error messages Built in buzzer for acoustically error indication Suitable for all battery types due to low dropout technology (NiCad, NiMH, LiPo, LiIon, LiFePo) Simple programming and operating An external on/off-switch can be connected as well (magnetically switch or pin-switch) New version 2.0 with more powerful voltage regulator (the measuring shunt has been replaced by a low impedance hall sensor element) For midsize models (F3A, F3A-X up to 2,5m, gliders, helicopters) with 5 up to 10 servos max. Delivery includes two brackets, mounting frame, screws, twofold JR/UNI connection cable, two MPX high current connectors incl. shrink hose, operating instructions German or English DPSI BIC Instructions	DPSI BIC $165
	DPSI BMS 1-channel (black) Battery Monitoring System / 1-Channel-Version Simply put in between current source (battery) and consumer (receiver, ignition system or similar) Turns on automatically (as soon as there is current) and turns off (if there is no current anymore) Displays all important measuring values in plain text: battery voltage, current, withdrawn capacity, operating time, minimum/maximum and average values Operating voltage range 6.0 volts up to 16.0 volts Maximum continuous current 10A (flow rate), 30A peak current Quiescent current approx. 12µA when turned off High precision 12 bit A/D converter for precise measuring values Programmable language selection (German or English) Delivery includes bracket, mounting frame, screws, operating instructions German or English DPSI BMS Instructions	DPSI BMS single battery $126
	DPSI BMS 2-channel (black) Battery Monitoring System / 2-Channel-Version Simply put in between current source (battery) and consumer (receiver, ignition system or similar) Turns on automatically (as soon as there is current) and turns off (if there is no current anymore) Displays all important measuring values in plain text: battery voltage, current, withdrawn capacity, operating time, minimum/maximum and average values Operating voltage range 6.0 volts up to 16.0 volts Maximum continuous current 10A (flow rate), 30A peak current Quiescent current approx. 12µA when turned off High precision 12 bit A/D converter for precise measuring values Total galvanically separation of both battery inputs and outputs (no electrically connection whatsoever) Programmable language selection (German or English) Delivery includes bracket, mounting frame, screws, operating instructions German or English DPSI BMS Instructions	DPSI BMS Dual Battery $138
	DPSI BIC external switch actuator (black) External switch actuator for the DPSI BIC Used, if there is no direct access to the push buttons of the DPSI BIC Includes ultra bright LED for operating and error indication Reverse polarity protected connector Delivery includes fiber glass mounting frame and screws	DPSI BIC ext. Switch $27.50 in stock