HKM Website

	Pulse amplifier with HF anti-noise filter for weak servo signals Amplifies the servo pulse from e.g. 2.7V up to the usal 4.8-5.0V level Fits ideal for the Futaba FASST system (6014 receiver) Suitable for long servo feed lines when not using a DPSI RV system Ferrite rings are dispensable due to the high efficient HF suppression filter Supply voltage up to 8.4 volts Simply put in between receiver and servo as extension cable Usable without soldering JR/Uni connection cable (3 x 0.34qmm / AWG22 cross section) with gold plated contacts Weight only 3 grams / 0.09 oz. Delivery includes operating instructions Signal booster instructions	$21 (ea) $81 (set of 4)
	DPSI V-Match The DPSI V-Match is a V-cable with integrated servo matching system for connection of two commercially available servos at a single receiver output (or DPSI output). One servo signal is fed through unchanged, the second one can be (re)-adjusted for direction, center position and end positions. No external programming device is necessary whatsoever (e.g. a PC or equivalent system). A simple magnet (included in delivery) suffices. Adjustment accomplished directly using the corresponding transmitter channel and remote control. Servo V-cable with adjustable matching for one of the servos' direction, center position and end positions Ideal for huge aerobatic models, where several servos actuate on one rudder, or e.g. for gliders, were both spoilers are controlled by two separate servos but only one receiver channel is left over DPSI V-Match is also optimally suitable for DPSI RV systems Pulse amplifier for weak servo pulses (e.g. Futaba FASST receiver 6014) Effective interference suppression with special LCL filters 0.34 mm2 thick connection cable and high grade connectors 4-layer PCB layout for highest packing density and maximum current load Operating voltage range from 4V up to 8.4V Resolution 3200 steps Programming simply accomplished using the delivered magnet and the remote control Delivery includes magnetically switch actuator and operating instructions V-Cable Instructions	$39.50 (ea) $135 (set of 4)
	Y-Cable 2 with UniTest2 adapter Servomatching for up to four servos with one receiver channel! For each servo separately adjustable: rolling direction center position servo running length limit speed one fail safe position Ideal for large aerobatic models, where several servos work on one rudder or e.g. for gliders, where two spoilers are manipulated by two servos, but there is only one receiver channel available The "Y-Cable 2" can also be used optimally in conjunction with the large DPSI RV systems Operating voltage starting from 3V Resolution 6400 steps (!) Programming via accompanied UniTest2 adapter (UniTest 2 prerequisite) German Instructions only	$65
	Y-Cable 2 separately Servomatching for up to four servos with one receiver channel! For each servo separately adjustable: rolling direction center position servo running length limit speed one fail safe position Ideal for large aerobatic models, where several servos work on one rudder or e.g. for gliders, where two spoilers are manipulated by two servos, but there is only one receiver channel available The "Y-Cable 2" can also be used optimally in conjunction with the large DPSI RV systems Operating voltage starting from 3V Resolution 6400 steps (!) Programming via external programming adapter or UniTest2 system using appropriate adapter (not included in delivery) Delivery includes operating instructions(german) but no programming adapter	$58
	UniTest 2 Allrounder ("all in one device suitable for all purposes") Current and voltage measuring device, RPM-meter, servo-tester with servo evaluation, servo pulse measuring device and scanner: in this modern measuring device you find all a model builder needs! Autarky operation due to built in battery Electrical driving measuring up to 50V and 80A with capacity- and energy measurement RPM measurement 1-20 blades with internal or external optical sensor Possibility to connect a digital scale for measuring thrust or torque (if corresponding test station available) Internal data memory for 2000 measuring values with adjustable sample rate (up to 5.5 hours recording!) Readout of data memory directly from device or data transmission of the values to a PC for further evaluation Possibility to connect a temperature sensor Servo tester (manual or automatic) with adjustable servo running length and fixed values for Graupner, Multiplex, Multiplex-Uni and Futaba Display for battery voltage and servo current at servo test Possibility for measuring servo pulses with indication of the pulse height in conjunction with scan receiver Scanning of the 35-, 40- and 41MHz frequency band with presentation of field strength as bars or in percent Stop watch with alarm function Free of cost software updates by PC with accompanying connection cable Using UniTest 2, the "Y-Cable 2" (servo match system) can directly be programmed All settings are accomplished like at a computer transmitter! Delivery includes connection cable for the PC and operating instructions (German)	$225